Indoor Guidance Screen Parking Guidance Control System
1 Product introduction
The indoor guidance screen is composed of a high-brightness LED module, a drive unit, a support and other parts. Installed inside the parking lot at important turnovers. Receive the output information of the centralized controller, display the number of empty cars in the area in the form of numbers, arrows, etc., guide the owner to quickly find the empty parking space, and ensure the smooth flow of the parking lot and the full use of the parking space.
2 Product Characteristics
1) The guide screen adopts aluminum profile + plexiglass shell, simple and atmospheric appearance;
2) The guide screen adopts low power consumption design, with short circuit, overvoltage, overcurrent, overload protection;
3) Multi-direction display content support, to meet the use of various intersections.
4) The indication is clear and recognizable, the lamp bead luminous intensity is high, the viewing distance is long, and the viewing Angle is wide;
5) Two-color high-light LED lamp beads, a variety of display options.
6) Mobile APP debugging address and arrow, debugging is convenient and fast.
7) Multi-directional guidance: You can set the multi-directional arrows "←", "↖", "→", "↑" and so on.
8) Red and green colors show the number of remaining parking Spaces, and the number of warnings can be customized. When the number of warnings is greater than the number of warnings, it will show green, and when the number of warnings is less than the number of warnings, it will show red.
3 Technical specification
|
Model |
WBP-IA31-1(one-way) |
Operating temperature |
-30℃ ~ +65℃ |
|
Size |
One-way 650*183*56mm |
Supply voltage |
AC220V±10 |
|
Two-way 1030*183*56mm |
Maximum power consumption |
≤20W(one-way) |
|
|
Three-way 1410*183*56mm |
Humidity |
5％--95％RH |
|
|
Appearance material |
Black aluminum frame |
Communication mode |
TCP/IP Bluetooth(debugging) |
|
Empty parking space |
Screen printing LED white luminous characters |
Communication distance |
TCP/IP≤200m Bluetooth≤5M |
|
Light source |
Red and green LED light beads |
Pixel density |
44321 point/㎡ |
|
Dot spacing |
4.75 mm |
Resolution ratio |
80*32=2560 point |
|
Life |
≥100,000 hours |
Drive mode |
constant current |
Table 3.1 Technical parameters of the indoor boot screen
4 Product installation
1) Profile hanger picture:
The lifting accessories for the guide screen are composed of two U-shaped lifts, the size of which is 30*30*40mm.
Fixing method:
(1) The main operation is to first clamp a U-shaped hanger into the profile groove with a screw,
(2) Insert the matching M8 screw into the small hole on the hanger, and fix the U-shape on the guide screen track.
(3) Connect the upper end with the screw or KBG tube to the fixed point.
The indoor guide screen is installed by ceiling hoisting, and the power and signal cables are directly led from the bridge to the guide panel box using metal hoses. The installation diagram is shown in Figure 4.1:
Figure 4.1 Installation of an indoor boot screen
5 Wiring schematic diagram
 |
Figure 5.1 Schematic diagram of wiring the indoor boot screen
6 Usage and maintenance
1) Non-system maintenance personnel shall not operate the system equipment at will to prevent misoperation and cause system failure.
2) After the system configuration file is completed, back it up to prevent it from being damaged and cannot be restored to reduce the maintenance workload.
3) Before replacing the faulty device, disconnect the power supply of the device to prevent the device from burning down during the operation.
4) When the system does not work normally, please check whether the power supply of each device is mistakenly turned off.
Hot Tags: indoor guidance screen for parking guidance control system, China indoor guidance screen for parking guidance control system manufacturers, suppliers, factory